How To Wire A Relay For A Backup Camera

Download Article

Download Article

A rear-view camera, also known every bit a backup photographic camera, lets y'all see what's behind your vehicle without having to await backwards. Though the device comes standard with many new motorcar models, y'all can add a rear-view photographic camera to your vehicle if it didn't come with one.

1. 1

   Buy a mountable backup camera for your specific vehicle. For safety, brand sure you buy a device specifically designed to be a rear-view camera. Purchasing one made for your specific vehicle volition make it easier to install than a standard aftermarket photographic camera. Then you can install it easily, look for a camera that mounts onto or direct behind your license plate.^[1]

   • Look for backup cameras at consumer electronics stores.

2. 2

   Go an external monitor if you want to proceed your existing rear-view mirror. An external backup monitor is a modest video screen that mounts onto your windshield similarly to a GPS. Though they take upward more than infinite than internal monitors, external monitors are far easier to see and tin be easily replaced if necessary.

   • If yous'd like, you can use a standard video monitor instead. However, keep in mind that it may not accept still features equally devices designed for use with backup cameras.

   Advertising

3. iii

   Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully functioning rear-view mirror that houses a pocket-sized screen inside the glass. Some internal monitors clip on top of your electric current rear-view mirror, but others supervene upon your original mirror entirely.^[2]

   • Most internal monitors close off and disappear when non in use, making them a perfect option if you want to preserve your machine's looks.

4. 4

   Buy ability and video cords if your camera and monitor didn't include them. For most rear-view camera installations, yous'll need camera and monitor splitter cords with connectors for video and power cables, 2 bare wire power cables, and an RCA video cablevision.^[iii]

   • Most installation kits include these cables, but some may require you lot to purchase them separately.
   • Some camera models use wireless transmitters instead of standard video cables.

   Advertising

1. 1

   Accept off your rear license plate. Using a Phillips caput screwdriver, remove each of the screws holding your rear license plate in place. Then, pull the plate off and set it aside.^[4]

   • Make certain you place the screws in a safe place and so you don't lose them.

2. two

   Remove your trunk's interior panel. Pop open up your body and wait for a solid interior panel covering the reverse side of your license plate mounting area. Then, insert a trim removal tool or other sparse device backside the panel and pry it off.^[5]

   • Removing this panel will expose the motorcar's rear wiring chambers.

3. iii

   Drill a small hole in the license plate mounting area. Make sure there are no obstructions betwixt the license plate mountain and the rear wiring chamber. So, create a small hole in the auto using a power drill equipped with a loftier-speed twist drill bit. Line upward your hole so it is directly backside where your camera's ability and video cable volition become.^[six]

   • To figure out where to brand the hole, hold your camera up to the area you lot intend to mount it. And then, annotation the spot where its splitting cord sits.
   • Create a hole that's big enough to fit your camera's power and video cable.
   • If you come up across any obstructions, try to remove them. If you tin can't, see if yous can make a pigsty nearby.
   • For nearly jobs, you'll need a drill fleck that has a diameter between ¹⁄₈ and ⁱ⁄_four  in (0.32 and 0.64 cm).

4. 4

   Place a safe grommet around your camera cable. Before running your camera cablevision into the car, slip a rubber grommet onto it near the non-splitting end. These small condom washers, available at most home improvement stores, volition keep the wire in identify and prevent leaks.^[7]

   • Choose a grommet that'southward just big enough to fit within the drilled hole.

5. 5

   Run the camera cable into your trunk. Pull the splitting cease of your camera's video and power cablevision through the drilled pigsty into the torso of your car. Make sure yous pull it tight and so the safe grommet lodges into the drilled hole.

   • Your camera cablevision should run from the outside of the car to the inside of the car.

6. six

   Locate your car's 2 contrary lite wires. Contrary calorie-free wires are the cords that connect your machine'south tail lights to the dashboard. They claw direct into your vehicle's tail lights and are commonly located in the hatch or body of your auto.

   • These cords look dissimilar for every vehicle then, if you can't find them, consult your possessor'due south manual for model specific information.

7. 7

   Strip and separate your machine's reverse light wires. Using a wire stripper or pliers, pare dorsum the rubber roofing the wires. So, use a screwdriver or other thin tool to poke a hole through the middle of each exposed wire, separating the individual wire strands.^[8]

   • For condom, make sure you practise this while the car is turned off.

8. 8

   Fuse your photographic camera wires with the opposite calorie-free wires. Attach 1 of your bare wire cables to the camera cord's ability connector. Then, poke your blank wires through the heart of the exposed reverse lite wires and twist them together. For safety, make sure you wrap the combined wires in electrical tape.^[9]

   • Make sure you lot poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually blackness) bare wire through the negative opposite light wire.

   Advertisement

1. 1

   Road your camera's video cablevision to the front of the car. Connect your RCA cable to the photographic camera cord's video connector if necessary. And then, run it through your vehicle to the surface area by the fuse box. Depending on your vehicle model, you'll usually be able to do this by peeling back the automobile'due south headliner or side panels and pulling your cable through the exposed chamber.^[10]

   • For certain trucks, you may demand to run the video cable through the vehicle's frame rail.
   • In most cars, y'all'll find the fuse box underneath the steering wheel.

2. two

   Ready external monitors to the front windshield. If you're installing an external monitor, first attach your device'southward included mount to the windshield by post-obit the manufacturer's included instructions. Then, hook your monitor onto the mount.

   • Well-nigh external monitors apply a suction mountain, though others may come with a more circuitous mounting system.

3. three

   Attach internal monitors to the rear-view mirror or mirror mount. For sure internal monitors, you'll need to prune the new device onto your current rear-view mirror. For others, you'll need to have off the mirror and slide your monitor into the pre-existing mirror mount.^[11]

   • Some internal monitors may come up with their own mounting organisation that yous'll have to attach to the car's front windshield.

4. iv

   Run the monitor'southward splitter cablevision to the fuse box. If necessary, claw your monitor's ability and video cable into the device. And so, route the cable from the monitor to the area side by side to the fuse box.^[12]

   • If you'd like, use a trim removal tool to popular out the headlining console directly above your windshield. And so, run your cablevision through the exposed sleeping room.

5. five

   Connect your monitor's camera cable to the RCA cablevision. After routing your monitor's splitter cablevision, connect the video end of the cable to your camera's RCA cord. And then, wrap the connected cords with electrical tape to concur them together.

   • If your RCA and video cables have the same ends, you may demand to buy an RCA male to female converter string. You tin can find these at nearly electronic stores.

6. 6

   Attach your monitor'south power cable to a fuse tap. Connect your remaining bare wire cable to the backup monitor'south power cord. And then, button the positive (unremarkably red) end of the bare wire cable into the open end of a fuse tap. Finally, crimp the ii cables together with a pair of pliers.^[13]

   • A fuse tap is a small cablevision that converts a bare wire into a fuse signal. You tin can find them at most auto part stores.
   • If you lot'd prefer, you can get out the bare wire cable off and connect your photographic camera'due south ability cable to a cigarette lighter adaptor. So, plug this adaptor into your car's cigarette lighter receptacle for power.

7. 7

   Plug the fuse tap into the fuse box. Locate your fuse box and open information technology up. So, plug your fuse tap into an open fuse cell. If necessary, check your fuse box'south lid or your vehicle'due south didactics manual to see which slots are open.^[14]

   • After attaching your fuse, consider taping all your wires together using electrical tape to get them out of the way.

   Advertisement

1. 1

   Connect your backup camera to its power and video cable. Render to the back of your auto in one case yous've installed the rear-view monitor and all the necessary camera cords. Close the trunk if necessary, then connect the fill-in camera to its power and video cable.

   • Your camera's power and video cablevision should exist sticking out of the hole you drilled in the license plate mounting expanse.

2. two

   Mount the camera to your license plate. If the camera attaches to the front of your license plate, fix it to the plate by following the manufacturer's included instructions. If the camera attaches to the dorsum of your license plate, line the device up with the plate'due south fastener holes and thread screws through them.^[15]

   • In well-nigh cases, you lot can adhere a rear-view photographic camera to the back of your license plate using the screws yous removed from the auto before.

3. 3

   Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. Once you've reattached it, requite the license plate and backup camera firm tugs to brand sure they're secure.

   • If you haven't already, reattach your car'due south interior trunk panel and other trim panels by pressing them back onto the vehicle.

4. 4

   Test the camera to brand sure everything works. Before using your new camera on public roads, test it in a safety area similar your driveway. If it turns on, place a large, durable object like a trash tin can behind the camera to see how distorted the epitome is. If it does not plow on, read your installation manual for troubleshooting information.

   • In many cases, rear-view camera malfunctions are caused by loose or improperly connected wires.

   Advertisement

Add New Question

• Question

  I hooked the camera up and it just flickers. Whatsoever communication?

  

  You may want to ensure all cables and connections are secured tightly. Double check that all connections are correct. If this doesn't piece of work, check to see if the camera called is in skilful shape and isn't physically damaged.

• Question

  Suzuki installed opposite parking camera in my Swift Dzire Zxi. But the camera shows upper view and not the ground below. What can I do ?

  

  Make certain that the camera is installed the correct way (not upside downwardly), and check the position of the camera mounted. Take information technology back to the dealer that installed it and ask them to check the alignment and fit.

• Question

  What is the best acme for a reversing photographic camera?

  

  There is no optimal height for a back-upwardly photographic camera. The platonic height is based off the specific automobile or vehicle that y'all have and your personal preferences, along with its intended application. Some back-up cameras are placed on large service trucks so that they can line up to trailer hitches easier, some are to forestall a blindspot on the route. Depending on your awarding, it tin can be placed at any height. Most reversing cameras are a "broad view" fashion and the specific height location does not e'er affect the fashion it functions.

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

• Though most machine dealers and mechanics will not install aftermarket backup camera systems, many audio and electronic shops volition.

Advertisement

• Brand sure you turn the car off before working with bare or stripped wires. If you demand to touch exposed wires while the auto is on, put on a pair of daze-resistant rubber gloves.

Advertisement

Things Y'all'll Need

• Rear-view camera
• Rear-view monitor
• Connector cables
• Phillips head screwdriver
• Trim removal tool
• Power drill with high-speed twist bit
• Rubber grommet
• Wire stripper or pliers
• Electrical tape
• Fuse tap

About This Article

Commodity Summary Ten

To successfully install a rear-view camera, first remove your vehicle's rear license plate and interior trunk panel. Using a ability drill, punch a pocket-size hole through the exposed license plate mounting area and run your camera'south power and video string through it. Attach a blank wire power cable to your photographic camera's power connector, then strip your car'due south reverse low-cal wires and splice them with your bare wire power cablevision. To learn how to mount the rear-view camera and backup monitor, scroll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 245,998 times.

Did this article aid yous?

Source: https://www.wikihow.com/Install-a-Rear-View-Camera

Posted by: millershorly.blogspot.com

Share this post